Mercury 150 hp 4 stroke service manual. DOWNLOAD 1965 2019-02-08

Mercury 150 hp 4 stroke service manual Rating: 4,9/10 1992 reviews

Mercury Verado 150 HP 4

mercury 150 hp 4 stroke service manual

If you intend to disregard this recommendation, and install the engine yourself, please make sure to read and comply with these instructions. Japan Telephone 81-053-423-2500 Mercury Marine - Japan Anshin-cho 283-1 Hamamatsu 81-053-423-2510 Shizuoka-ken, Japan 435-0005 Japan Asia, Singapore Telephone 5466160 Mercury Marine Singapore 72 Loyang Way. Add Quicksilver or Mercury Precision Lubricants Power Trim and Steering Fluid. Pull the propeller straight off the shaft. Locate the center point of the slack or lost motion that exists in the shift cable as follows: a. The operator must have an unobstructed view particularly to the front. After start-up, the current supplied form the electric power source and then flows to the electrothermal valves causing the wax in the valves to heat up.

Next

MERCURY 150 MANUAL Pdf Download.

mercury 150 hp 4 stroke service manual

For visual display of the specific engine functions and additional engine data, refer to SmartCraft Product information, following. Description Where Used Part No. The clips at either end of the shaft and at center are known as retainers, while the other two on either side of the center retainer are normally called tensioners because they should have an overload spring mounted under them. Open the fuel tank vent screw in filler cap on manual venting type fuel tanks. Remove flywheel cover and spark plug cover.

Next

Mercury 2

mercury 150 hp 4 stroke service manual

All of the spark plugs should have the gap checked and corrected as necessary before installation. Minimum Transom Opening Single engine 84. The cost to diagnose a warranty failure is covered under the warranty if the warranty claim is approved. Place the lubricant tube into the fill hole and add the lubricant until it appears at the vent hole. Do not allow the Corrosion Guard spray to come in contact with the alternator drive belt or belt pulleys. Flywheel cover Screws 3 47585 2.

Next

Mercury Outboard Marine Service and Repair Manuals from Clymer

mercury 150 hp 4 stroke service manual

This additional air flows into the carburetors and mixes with the fuel from the main jets. Ensure that the key switch is off and the lanyard is positioned so that the engine cannot start. Refer to General Information - Lanyard Stop Switch. It operates in html format meaning it operates just like a web site. Oil from the oil injection system will supply adequate lubrication during engine break-in.

Next

DOWNLOAD Mariner/Mercury Troubleshooting Repair Manuals

mercury 150 hp 4 stroke service manual

The propeller shaft should be locked in gear. Remove the three screws that fastens the flywheel cover to the engine. The manual covers a wide range of topics from general information about your Seloc motor to fuel systems, lubrication, powerheads and more. Position the opposite end of the hose into an appropriate container. Remove driven sprockets and timing belt. Secure the shift cable to the anchor pin with the bow tie clip retainer.

Next

Mercury 30 / 40 Hp 4

mercury 150 hp 4 stroke service manual

If the propeller is seized to the shaft and cannot be removed, have the propeller removed by an authorized dealer. It is generally similar to the Yamaha system with only a few component differences. Keep the work area well ventilated and avoid prolonged exposure to vapors. If not, consult your dealer for a description of the functions and operations of the remote control. Place a block of wood between the gearcase and the propeller to hold the propeller and remove the propeller nut. Battery cable terminals should be clean, tight, and correctly installed. The most important thing you can do to help reduce injury or impact damage from striking a floating or underwater object is to control the boat speed.

Next

Mercury 30 / 40 Hp 4

mercury 150 hp 4 stroke service manual

Carefully pry up the valve pad and remove it. Slowly return the handle back to the neutral detent position. Turn the flywheel 360° clockwise. Priming will remove any air that may be in the pump, oil supply hose, or internal passages. Before lifting the outboard, verify that the lifting ring is threaded into the flywheel for a minimum of five turns and that the hoist has the correct lifting capacity for the engine weight. Measure and record the intake valve clearance for cylinders 1 and 2. Oil should be in the operating range between the top bar and bottom bar.

Next

Mercury Outboard Marine Service and Repair Manuals from Clymer

mercury 150 hp 4 stroke service manual

If you key the engine off and restart it, the horn will sound again, one time, if the fault is still present. Save all maintenance work orders and receipts. The following storage procedures should be followed to prepare your outboard for out of season storage or prolonged storage two months or longer. Refer to your Operation and Maintenance Manual for full details of your warranty coverage. If purchaser cannot deliver the product to such a dealer, please notify Mercury Marine and Mercury will then arrange for the inspection and any covered repair.

Next