Keeprite split system manual. [PDF] Keeprite split system manual: musical 2019-01-25

Keeprite split system manual Rating: 8,7/10 1418 reviews

KEEPRITE DLFCAB INSTALLATION INSTRUCTION Pdf Download.

keeprite split system manual

Hold the horizontal louver with right hand to separate connection rod and horizontal louver. You may read Keeprite n9mp manual online either download. Keeprite Split System Manual Document about Keeprite Split System Manual Download is available on print and digital edition. Pull out the wiring terminal and pull it electric box upwards to remove the electric box. Remove swing blade 328 080000 01 Specifications subject to change without notice. Insert the temperature sensor tightly Is malfunction eliminated Is there a short circuit? View online or free download from eBooks-go.

Next

KEEPRITE DLFCAB SERVICE MANUAL Pdf Download.

keeprite split system manual

Please expand the pipe according to the following steps: Pipe a. Hold the end of connection rod with left hand. Is there a malfunction in the discharge temperature sensor? These problems are typical This section provides the required flow charts to troubleshoot problems air conditioning mechanical or electrical issues that can be corrected that may arise. Determine pipe hole position using the mounting plate as a Ideal installation locations include: template. Next, remove the front panel. Pass interconnecting cable through hole in wall outside to inside. Cut the pipe Confirm the pipe length according to the distance of the Fig.

Next

[PDF] Keeprite n9mp manual

keeprite split system manual

Detect the indoor and outdoor units connection wire and indoor and outdoor units inside wiring is connect well or not, if is there any damage? Is the electronic expansion valve damaged? Remove gas valve and liquid valve Twist off the 2 bolts fixing the valve sub-assy. Is connection wire loosened or pulled out? Remove the electric box Twist off the screws on the electric box, and cut off the tieline with scissors or pliers. Communication malfunction E6 Main detection points: Check if the wire is damaged or the polarity is mixed between terminals. Remove the horizontal louver along the center axle. Piping Length Standard Piping Length Max.

Next

KEEPRITE DLFCAB INSTALLATION INSTRUCTION Pdf Download.

keeprite split system manual

Remove the 4-way valve assy 4-way valve assy Unscrew the fastening nut of the 4-way Valve Assy coil and remove the coil. Valve cap Refrigerant charging 2. Get solutions from Household Appliance experts. Remove the 2 tapping screws securing the motor support. Pull it upwards and then remove the motor support. Remove electric box electric box Twist off the screws on electric box, cut off the tieline with scissors or pliers, pull out the wiring terminal, pull it upwards to remove the electric box. Remove the screw connecting the valve cover and right side plate, and then remove the valve cover.

Next

[PDF] Keeprite n9mp manual

keeprite split system manual

Online ordering for air conditioning parts, heating parts and furnace parts. Push the rotor shaft on both sides of the panel to separate it from the groove. Malfunction of Temperature Sensor F1, F2 Troubleshooting for F1,F2 malfunction the wiring terminal between the temperature sensor and the controller loosened or poorly contacted? If yes, No power supply or poor connection for power After energizer, operation indicator is not bright wait for power recovery. Connect the line Correct connection? Twist off the screws on electric box fireproofing electric box with screwdriver, and then remove the electric. Communication Malfunction E6 Start Cut off power supply. Assemble the jumper cap with the same model Is malfunction eliminated the jumper cap inserted correctly and tightly? Turn on the unit Is the charge in the system correct and Does the unit turn on have you opened both liquid and within 3min? Remove the chassis and condenser Pull it up to separate the chassis and condenser. Is reactor L well connected? Remove the grille and panel Twist off the screws connecting the grille and panel.

Next

KEEPRITE DLFCAB SERVICE MANUAL Pdf Download.

keeprite split system manual

Overload and high discharge temperature malfunction Is the overload protector damaged? Run interconnecting piping and wiring from outdoor unit to indoor unit. Lift the motor support to remove it. Remove the left side plate Twist off the screws connecting the left side plate and chassis with a screwdriver ,. Is the indoor and outdoor fan running normally? If you have necessity to download pdf Keeprite n9mp manual , then you've come to loyal site. Main detection points: Is the heat exchange plugged or cracked? Remove the right side plate Remove t h e connection screws connecting the right side plate right side plate with the valve support and. Is the heat exchanger dirty? Lift indoor unit into position and route piping and drain Fig.

Next

Support

keeprite split system manual

Remove isolation sheet Twist off the screws connecting isolation sheet and end plate of condenser and chassis, and then remove the isolation sheet. Make sure all parts fastened tight. Remove the motor support Twist off the tapping screws securing the motor support. Malfunction diagnosis process: Did the unit operate normally before malfunction? Download 1995 jetta glx repair manual. Is the communication circuit of the indoor mainboard damaged? These factory specified parts are available through our authorized distributors throughout North America.

Next

KEEPRITE DLFCAB INSTALLATION INSTRUCTION Pdf Download.

keeprite split system manual

Only when the remote control signal is switched to the indoor vent ambient temperature display status corresponding remote Nut of refrigerant. For more information, please contact our head office or your local sales representative. Other Model Numbers Referenced to The Same Manual. Pull out the lead-out wire and remove the motor. Main board matches Match correctly with display board? Remove the isolation sheet Twist off the screws connecting the isolation sheet and end plate of the condenser and chassis. Keeprite N9mp Manual If searched for the ebook Keeprite n9mp manual in pdf format, then you've come to correct site. Is the condensing unit blocked with dirt and debris? Remove grille and panel Twist off the screws connecting the grille and panel, and then remove the grille.

Next

[PDF] Keeprite n9mp manual

keeprite split system manual

We will be pleased if you get back to us over. Abbreviated model: It is recommended that you use 3-5 characters in your search. Is the electronic expansion valve connected to the board? Is the ambient temperature too high? Wrap the 4-way Valve Assy with wet cotton and unsolder the 4 weld spots connecting the 4-way Valve Assy to remove. Remove cross flow blade and motor Specifications subject to change without notice. Malfunction of Protection of Jumper Cap C5 Troubleshooting for C5 malfunction Appearance of Is there jumper cap on the the jumper cap mainboard? Unsolder the soldering joint between gas valve and air-return pipe and then remove the gas valve.

Next

KEEPRITE DLFCAB INSTALLATION INSTRUCTION Pdf Download.

keeprite split system manual

Piping Length Standard Piping Length Max. Unsolder the soldering joint between gas valve and air-return pipe and then remove the gas valve. Remove left side plate Twist off the screws connecting the left side plate and chassis with screwdriver, and then remove the left side plate. Main board of Malfunction eliminated? For support for obsolete, discontinued or previous generation products. Twist off the screws connecting the panel, chassis and motor support with screwd-river, and then remove the panel. When the user sets the remote controller to display the set temperature corresponding remote control code: 01 , the current Gas valve set temperature appears.

Next