Highlander fuse box diagram. Toyota Highlander Owners Manual: Checking and replacing fuses 2019-02-11

Highlander fuse box diagram Rating: 4,1/10 938 reviews

Interior Fuse Box Location: 2001

highlander fuse box diagram

Remove the chrome bracket and the black plastic cap. Refer to the diagram on the following page for general motorcycle box wiring information Remove the stock steering box and column. See page 6-7 for panel removal and installation procedures. In no way does Wiring Diagram Pictures claim ownership or responsibility for such items, and you should seek legal consent for any use of such materials from its owner. We thank you for your visit to our website. Obtain the new left-side glove box door, hinge and frame assembly 1 , a lock 2 and a tether assembly 8 from the kit. You will attach the two that you removed to the right side bracket in Section 4C.

Next

Toyota Highlander (XU40; 2008

highlander fuse box diagram

Because certain bulbs are connected to circuits designed to prevent overload, non-genuine parts or parts not designed for this vehicle may be unusable. Toyota has an improved relay available, and can be purchased at any Toyota parts department. Extra weight from items, such as bags or groceries or toys, hanging on the seat back can add to the sensed weight of the front seat passenger. Bolt the bracket directly into the mounting holes for the original steering box. If they do not pull off easily, you can raise or lower the bike slightly with the lift to ease tension on the spring. Attach the pitman arm to the steering box. Notice Before replacing fuses Have the cause of electrical overload determined and repaired by your toyota dealer as soon as possible.

Next

Toyota Highlander II XU40 Fuse box diagrams & schemes

highlander fuse box diagram

Turn the shaft back half the distance and now the box is centered. Now turn the shaft counter clockwise as far it can go and be sure to count the turns. A white plastic fuse puller tool is included on the underside of the engine bay fuse box cover. Some components may have multiple fuses, so make sure you check all of the fuses that are linked to the component in question. If a headlight bulb burns out, replace it as follows.

Next

Toyota Highlander (XU20; 2004

highlander fuse box diagram

Be sure to double and triple check this procedure. Battery box — Remove the two bolts that hold the battery box to the frame. Make sure the splined shaft goes through the frame without interference. If the fuse immediately blows again, have a Yamaha dealer check the electrical system. Some components may have multiple fuses, so make sure you check all of the fuses that are linked to the component in question. If this happens, check and replace the fuses as necessary. Spare fuel injection system fuse 1.

Next

Fuse box diagram for a toyota highlander 2002

highlander fuse box diagram

Vehicles with a smart key system: turn the engine switch off. Earlier models may have the standard , which are slightly taller. Bolt the Toyota box to the mounting bracket so that the long arm of the bracket points in the same direction as the steering column input shaft small shaft. Torque down the mounting bolts to 45 lbs. If a fuse is blown, replace it as follows. If you removed it, push on the relay box cover on the right side of the engine bay.

Next

2003 Toyota Highlander Fuse Box Diagram

highlander fuse box diagram

Note: Your luggage rack may already have the correct mounting holes drilled. See page 6-7 for panel removal and installation procedures. Bolt the Toyota box to the mounting bracket so that the long arm of the bracket points in the same direction as the steering column input shaft small shaft. There are several parts that must be removed in order to get the air-box out of the bike in one piece. The resistance of the wires should be below 1 Ω. Before this is done the steering sector must be centered. Please click next button to view more images.

Next

Toyota Highlander (XU20; 2001

highlander fuse box diagram

The fuel injection system fuse box is located under panel D. Go through the list and click the required link:----- 2009 Toyota Corolla: Fuse Box Module Removal? Be sure to double and triple check this procedure. Remove panel B if replacing the left headlight bulb or panel C if replacing the right headlight bulb. Voltage should be between 2. Underneath the side cover there are three rubber grommets 1 on the frame tab, and two on the air-box that support the side cover.

Next

2001 Toyota Highlander Fuse Box Diagram. Toyota. Auto Fuse Box Diagram

highlander fuse box diagram

The resistance of the wires should be below 1 Ω. Unsnap the original equipment O. If checking and replacing the fuse for the component in question doesn't work, we recommend seeking assistance from a trusted professional mechanic. Bolt the bracket directly into the mounting holes for the original steering box. If you need to replace a blown fuse in your Highlander, make sure you replace it with one that has the same amperage as the blown fuse. Peel one half of the liner from the adhesive backing of the left-side gasket.

Next

Toyota Highlander II XU40 Fuse box diagrams & schemes

highlander fuse box diagram

If you need to replace a blown fuse in your Highlander, make sure you replace it with one that has the same amperage as the blown fuse. Insert the lock through the hole in the glove box door as shown. There are many fuses that controls dash panel and on-dash lights. Pull off the retaining clip on the rear edge of the fuse panel cover, located closest to the front of the vehicle. Pull the battery box out as far as you can, then remove the the ignition terminal from the battery box, by removing the two allen screws that hold it in place from the back. Align the 5 vibration dampeners with the 5 mounting holes in the mounting plate. Have someone hold the fender for you while you are removing all of the bolts so that it does not drop once the bolts are removed.

Next

Toyota Highlander Owners Manual: Checking and replacing fuses

highlander fuse box diagram

Attach the pitman arm to the output shaft with the output shaft nut. There is a white plastic fuse puller tool attached to the underside of the fuse box cover along with a fuse location diagram. Obtain the left-side gasket 6 and a hinge gasket 7 from the kit. We hope you like it as we do. Once all the bolts are removed gently pull the springs out off of the studs. Press in the release tab on the front of the box and pull off the black plastic cover.

Next