Harley davidson softail 2003 owner manual. HARLEY 2019-01-28

Harley davidson softail 2003 owner manual Rating: 7,8/10 760 reviews

HARLEY

harley davidson softail 2003 owner manual

Table 3 lists motorcycle weight. Pin Housing and Circuit Board Install new base to rear fender. The torque adapter shown in Figure 22 is used to tighten a fastener that cannot be reached due to the size of the torque wrench head, drive and socket. When the ignition switch is turned on and the start but- ton is pushed in, current is transmitted from the battery to the starter relay. Right crankcase half Figure 3-53.

Next

2003 Harley

harley davidson softail 2003 owner manual

Clean the anvil and spindle faces. The neutral switch is located on the transmis- sion top cover. As the bearing chills, it will tighten on the shaft, so installation must be done quickly. Always place a piece of metal between the end of the shaft and the puller screw. Reading a Micrometer When reading a micrometer, numbers are taken from different scales and added together. Pinched throttle cables can restrict throttle response, which could result in loss of control and death or serious injury. Slide short shift shaft through countershaft shifter sm03601 forks and install shaft in hole in side door.

Next

List of Harley

harley davidson softail 2003 owner manual

Worn or damaged camshaft gear s. A stan- dard gauge is a steel block, disc or rod that is machined to an exact size. Connect the red test lead to the elec- trical source and the black test lead to the electrical load. The rear stoplight switch monitors brake fluid After repairing the brake system, test brakes at low speed. An ohmmeter will indicate ei- ther low or no resistance if the circuit has continuity.

Next

2003 HARLEY DAVIDSON softail owners manual heritage fatboy night train springer

harley davidson softail 2003 owner manual

Remove push rods and push rod covers. Dial indicators are available in various ranges and grad- uations, and with three basic types of mounting bases: magnetic, clamp, or screw-in stud. Following the sequence shown, altern- ately loosen the six rocker housing bolts. Reaming Valve Guide Bore Figure 3-104. Small retainers connect the vent line 3 to the oil tank and to the engine. When install- ing a new bearing, take care to prevent damaging it.

Next

HARLEY

harley davidson softail 2003 owner manual

Do not Hoses, clamps, electrical wiring, electrical switches or fuel lines work on two assemblies simultaneously. Shifter engaging parts inside transmission badly worn Oil pump o-ring damaged or missing. Never force the caliper closed around an object; close the caliper around the highest point so it can be removed with a slight drag. Install oil tank drain plug 2. See Snap Ring Pliers in this chapter.

Next

2003 Harley

harley davidson softail 2003 owner manual

Do not remove lifters or lifter covers. Clean the air cleaner element. Severely contaminated air filter element. Rotate forcing screw to compress valve spring. While riding, a loose seat can shift Clean the tank interior with commercial cleaning solvent causing loss of control, which could result in death or or a soap and water solution. Every fifth mark above the sleeve line is identified with a number.

Next

2003 Harley Davidson Softail Motorcycle Service Manual

harley davidson softail 2003 owner manual

Cartridge body is fully installed when reservoir adapter contacts large retaining ring. A-19 Removing Terminals from Housing. Apply clean H-D 20W50 engine oil to 3. For laced wheels, see 2. Remove bearing 1 and dust shield 2 from fork stem. Torque wrenches are covered in the Basic Tools section. A continuity test can determine if the circuit is com- plete.

Next

2003 Harley Davidson Repair, Owner & Part Manuals

harley davidson softail 2003 owner manual

To read a vernier caliper, refer to Figure 29. Check wheel bearings and axle spacers for wear and corrosion. Jumps Out Of Gear Low Oil Pressure Shifter rod improperly adjusted. Install remaining nine upper row spokes. The materials used to form the lock become distorted after the initial installation and removal. Table 1 lists model designation. Mating Pin and Socket Housings Push pin and socket halves of connector together until external latch es engage.

Next