Exmark lazer z xp operators manual. Exmark Lawn Mower Manuals 2019-01-28

Exmark lazer z xp operators manual Rating: 4,7/10 1577 reviews

Exmark Lawn Mower Manuals

exmark lazer z xp operators manual

It is essential that all Operator Safety Mechanisms be connected and in operating condition prior to use for mowing. Use coolant specified in Section 2. Tilt seat forward to gain access to the tracking knob. Coolant may be drained from the radiator by loosening the drain cock in the right rear corner. If it does not start, contact your authorized Exmark service dealer. Use only Mobil 1 15W-50 synthetic motor oil.

Next

Exmark LAZER Z series Lawn Mower Operator's manual PDF View/Download

exmark lazer z xp operators manual

Clean area around hydraulic reservoir cap and remove cap. Summary of the content on the page No. If you want to quickly view the content of pages found on the following pages of the manual, you can use them. This product has been carefully designed and manufactured to give you a maximum amount of dependability and years of trouble-free operation. Install the left motion control lever onto the control arm shaft See Figure 5 on the left side of the console. Oil level should be to the top of the baffle inside the tank.

Next

Exmark LAZER Z series Lawn Mower Operator's manual PDF View/Download

exmark lazer z xp operators manual

Use the fuel from the right fuel tank first. In 1987, due to the rapidly growing turf care equipment market and the competitive nature of that market, the product line was expanded to include commercial riding mowers. Run engine at full throttle and release brake. If necessary fill with coolant as described in Section 5. It is essential that all Operator Safety Mechanisms be connected and in operating condition prior to use for mowing. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual.

Next

Exmark Lazer Z XP user manual

exmark lazer z xp operators manual

Note: Make sure the bent tab in the washer is towards the head of the bolt. Familiarize yourself with the controls and the proper use of the equipment. It is important that no dirt or contamination enter hydraulic system. Check to make sure brake is adjusted properly. When the right fuel tank is empty switch to the left fuel tank. You by us in the exercise of our reasonable discretion to be. Tension in throttle lever can be adjusted by adjusting the tightness of the lever pivot bolt, which is located under the console See Figure 17.

Next

EXMARK LAZER Z XP OPERATOR'S MANUAL Pdf Download.

exmark lazer z xp operators manual

Check distance from bottom of slot in nut to inside edge of hole. Check to make sure the coils of the spring on the spring-loaded idler pulley measures as listed below. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase. Brake must be engaged and motion control levers out to start engine. Stop engine and wait for all moving parts to stop. Avoid sudden acceleration when driving up a ramp and sudden deceleration when backing down a ramp. Lightly oil the inside surfaces of the ear-shaped plates at the upper end of the lower roll bar tubes.

Next

Exmark Lazer Z XP user manual

exmark lazer z xp operators manual

If more than two threads 0. Remove key before adjusting, servicing, or performing maintenance. How the Program Works 1. Indicates an imminently h Summary of the content on the page No. Units also have a foot operated deck lift assist lever to aid in raising the deck. The cutting height adjustment handle has a transport position and all adjustments can be made while the operator remains seated. Drain oil while engine is warm from operation.

Next

Exmark Lawn Mower Manuals

exmark lazer z xp operators manual

When levers are centered in the T-slot the drive system is in the neutral position. Remove the oil drain plug. Insert 1 bearing, 1 new seal into the wheel. Set anti-scalp rollers to top holes or remove them completely for this adjustment. Held in tilted position with prop rod. See decals on the side of deck lift plate. Insert the assembled nut and axle into the wheel on the side of the wheel with the new seal and bearing.

Next

Exmark Manuals

exmark lazer z xp operators manual

Check the oil level and fill, if necessary, as described in Section 5. Carefully clean area around filter. Self-tensioning idlers, adjust as follows: Stop engine, wait for all moving parts to stop, and remove key. All Exmark equipment dealers and distributors are kept informed of the latest methods of servicing and are equipped to provide prompt and efficient service in the field or at their service stations. Operator does not have to be in the seat. Turn the unit off, allow the engine and engine components to cool.

Next