The exit time may be changed by your installer please refer to the Quick-Arm feature. If the system has not been programmed for this automatic lest, call the monitoring station for instructions on how to perform a test transmission. If the detectors still have smoke in them, the alarm will sound again. Press any key to silence keypad beeping. For other system devices such as smoke detectors, passive infrared, ultrasonic or microwave motion detectors or glassbreak detectors, consult the respective manufacturer's literature for testing and maintenance.
If the smoke detector is reset but goes into alarm again after the 90-second delay, the fire alarm will sound again and the process described above will repeat. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · A good plan emphasizes quick escape Do not investigate first or attempt to fight the fire, and do not attempt to rescue belongings or pets as this takes up valuable time. When a Fire Alarm is generated, the bell or siren will sound with a pulsing tone. In the case of such temporary discontinuance, the telephone company shall promptly notify the customer and will be given the opportunity to correct the situation. When the correct code is entered and the system is armed, exit through the door indicated by your installer as the exit-entry door. To do this, first inform the monitoring station that you are testing your system.
When testing is complete, call and advise the monitoring station. Arming and Commercial Installations When an Access Code is entered to arm the system, the bell or siren will sound a short tone to indicate that the system is being armed. · Exits on the ground level should be kept clear. · If opening the exit or using the exit is too difficult for children, the elderly or handicapped. Read this manual carefully and become familiar with the operation of your Security System. As each digit is entered, the keypad sounder will beep.
Light dusting with a barely damp cloth should remove normal accumulations of dust. To reset smoke detectors to normal, first clear all products of combustion from the detectors. Be sure to remove snow from exterior patio doors in winter: outdoor furniture or equipment should not block exits. If programmed as audible, the alarm bell will ring. Activate each sensor in turn. When a sensor is in alarm, a keypad light will be on to indicate which zone is in alarm.
Equipment Maintenance Facility If you experience trouble with this telephone equipment, please contact the facility indicated below for information on obtaining service or repairs. The keypad is used to send commands to the system and to display the current system status. Do not wash the keypad with a wet cloth. Are fire hazardous materials matches well out of reach of children? This is useful if you want to exit while preserving the protection for someone left on the premises. The security system has up to eight zones or areas of protection. Those interior zones have been designated as home-away zones by the installer.
The entry delay time may be changed by the installer. · If the exit is above the ground level, an approved fire ladder or rope should be provided as well as training in its use. To arm without entry delay. See the Trouble Display section in this manual for a description of the different trouble conditions Contact your installer for assistance if the trouble condition cannot be located and corrected. Unsuccessful Communication Attempt with Monitoring Station 5.
If available, have your local fire prevention officer conduct an in-house fire safety inspection. . . Zone bypasses are automatically canceled each time the panel is disarmed and must be re-applied before the next arming. · It is essential that escape from a bedroom be possible without opening the interior door.
Then, with the system disarmed, activate all detection sensors one at a time and observe the zone light come on at the keypad as each sensor is activated. Refer to zone chart on keypad door for zone information. Check for frayed cords, over-loaded lighting circuits, etc. Changes In Telephone Company Equipment or Facilities The telephone company may make changes in its communications facilities, equipment, operations or procedures, where such actions are reasonably required and proper in its business. If you are unsure about system operation, contact your installing dealer.
If you exit within the allowed exit lime, the system will automatically reactivate the interior zones. Ensure that plugs and jacks meet the dimension, tolerance and metallic plating requirements of 47 C. It is only intended to alert you in case of an emergency and should not take the place of prudent security practices or life and property insurance. Enter 1 for zone 1. They will advise what action has been taken as a result of the alarm and whether the premises are safe to enter.