Press the hub out of the bearing race. Crankshaft for Chrysler Pt Cruiser 2001. Using a 3 step torque method as gasket in the vertical oil passage to the cylinder follows: head is plugged with debris. While holding the camshaft sprocket with Special Tool 8435, torque bolt to 115 N·m 85 ft. They may not show exactly the Chrysler Pt Cruiser 2001 in your possession.
Low speed running up to 1 hour may be ulator to the dipstick tube. Tighten the wheel mounting nuts to a torque of 135 N·m 100 ft. Test and repair charging system. This is referred to as Net Build. Piston and cylinder wall must be clean and dry.
Replace the engine air cleaner filter. The crankshaft is supported by five main bearings. Refer to the appropriate wiring information. Remove Special Tool 8446 from cylinder head Fig. The battery tray provides a secure mounting loca- 4 One at a time, trace the battery cable retaining tion and supports the battery. Replace cylinder head if they are not within specification.
The right mount is a hydro-elastic mount and left mount is a conventional elastomeric isolator. Refer to replacing the wheel speed sensor or tone wheel. See the instructions provided by the manufac- battery will endure a load test, return the battery to turer of the battery charger for details on how to service. Charging System for Chrysler Pt Cruiser 2001. G100 Gas Left Front Engine Compartment 2, 5, 6 G100 Diesel Below Passenger Seat 7, 48 G101 At Battery Tray 5, 6, 7, 18 G102 Left Fender Area 1, 14, 16 G103.
Be careful not to damage retention tabs on bearing. The heating element immersed in coolant Fig. Inspect oil pump relief valve and spring. Use care not to over-fill reservoir and spill fluid into engine compartment. If the ball the steering knuckle and allows for the up and down joint is lubricated after installation to knuckle, dam- movement of the suspension during the jounce and. This manual for Chrysler Pt Cruiser 2001 has been issued to provide you with technical information regarding the design, function, disassembly, adjusting work and troubleshooting on the components and model of the Chrysler Pt Cruiser 2001. To maximise the life of your Chrysler Pt Cruiser 2001: Accurately follow the maintenance requirements of the periodic maintenance chart in the service manual.
Visually verify clutch disc alignment. This Chrysler Pt Cruiser 2001 service manual provides data, characteristics, instructions and methodology to perform repair interventions on the vehicle and its components. Torque fasteners to 28 N·m 250 in. One of the two hydraulic circuits is 1. Power Assisted Steering System for Chrysler Pt Cruiser 2001. Do Non-Turbo not damage the main bearings or journals when The crankshaft is supported in five main bearings. Tighten the mounting screw to a torque of 13 N·m 120 in.
Polish with 400 grit paper if necessary. Install a new retaining clip on the end of the pin Fig. Rectify all problems as soon as possible immediately if safety related. Refer to the Battery section solenoid for indications of physical damage and loose for more information. All this information is intended to simplify any necessary repair work which can be performed on Chrysler Pt Cruiser 2001.
The vehicle's service schedule includes weekly engine coolant level checks, three-monthly engine oil and filter changes, and yearly drive belt checks. The valve stem seals should be pushed firmly and squarely over valve guide. To achieve the cross camber reading, as viewed from above the vehicle Fig. The Fuse Block is serviced with the instrument panel wire harness. Engine Electrical Devices for Chrysler Pt Cruiser 2001.
This seal provides a hydraulic seal between the piston and the cylinder wall Fig. Charge or replace as necessary. Discard the original brake lamp switch. If gauge pulsates with every power stroke of a cylinder a combustion pressure leak is evident. Follow the procedures in this manual carefully and completely. Adjustment and repair operations include reference to Service tool numbers and the associated illustration depicts the tool for Chrysler Pt Cruiser 2001. The switch can only be adjusted once.
Final Drive for Chrysler Pt Cruiser 2001. Remove intermediate pipe from catalytic con- verter pipe Fig. Install the seat airbag retaining nuts. Do not take short cuts. High or low oil level in 1. Wipers and Washers for Chrysler Pt Cruiser 2001.