. Remove the two screws 1 that secure the front of the console shifter bezel to the console. Slide the trim stick down to the lower spring clip retainer, and pry to disengage clip. Always wear safety goggles when working on vehicles or vehicle components. Choose the Haynes manual that is right for you with our complete comparison guide Printed manualThe original and best, delivered to your door Online manualA feature-loaded digital edition of the original manual MaintenanceSimple weekly checks and servicing guides to keep you on the road Printed manual Digital manual Servicing Complete, fully illustrated step-by-step guides Printed manual Digital manual Easy search Find the task you are looking for quickly Printed manual Digital manual Print-at-home Take the sections you need to the workshop Printed manual Digital manual Wiring Easy-to-read electrical diagrams Printed manual Digital manual Color photosWhich can be enlarged Printed manual Digital manual Watch and learn Video tutorials for many common tasks Printed manual Digital manual Printed manual The original and the best, delivered to your door Introduction Chapter 1: Tune-up and routine maintenance Chapter 2: Part A: 2.
Tighten the screws to 3 N·m 23 in. The service produces recommended and described in this publication were developed for professional service personnel, and are effective methods for performing vehicle repair. A battery reconnect procedure must be performed anytime the battery has been disconnected. Insert trim stick from the outside in the direction of arrow 2 under the middle of the part. If you work on your own Chrysler 300 300C 300 Touring Sedans and Dodge Magnum or need additional information then this is the compilation for you.
Install and tighten the two screws 1 that secure the front of the console shifter bezel to the console. Some service procedures require the use of special tools designed for specific procedures. Contains technical data, spare parts illustrations and detailed illustrations, including exploded view diagrams. While holding both sides of the console at the front carefully engage the ears at the front of the console to the slots 5 at the lower instrument panel. Install and tighten the two screws 3 that secure the front of the console to the instrument panel.
The tips and instructions for repair, maintenance and operation given in the book will help the owner of the machine to prepare for the technical inspection procedure and also collect valuable, necessary, and often simply irreplaceable information in case of repair in the usual garage workshop, and in repair The operations at the service stations will serve a very important and useful advisory function. Position the console shifter bezel 4 over the gear selector lever. It is important to note that these Cautions and Warnings cover only the situations and procedures DaimlerChrysler Corporation has encountered and recommended. Remove the mat from the cubby bin at the front of the floor console. Remove the upper cowl trim from the vehicle.
Recommended servicing requirements for the Chrysler 300 include annual brake system checks, air filter replacement every 30,000 miles, and regular oil and filter checks. Regular servicing and maintenance of your Chrysler 300 can help maintain its resale value, save you money, and make it safer to drive. Remove the lower cowl trim from the vehicle. Reconnect the battery negative cable. Turn the ignition switch to the Off position and release the service brakes.
Proper service and repair is important to the safe, reliable operation of all motor vehicles. A battery recon- nect procedure must be performed anytime the battery has been disconnected. Special attention should be exercised when working with spring-or tension-loaded fasteners and devices such as E-Clips, Circlips, Snap rings, etc. Turn the ignition switch to the On position, apply the service brakes and place the gear selector lever into the Neutral position. Position the floor console into the vehicle rearward far enough to access and reconnect the jumper wire con- nector 4 to the accessory power outlet on the underside of the console.
Disconnect and isolate the battery negative cable. Following these procedures will help ensure efficient economical vehicle performance and service reliability. Remove the shifter bezel from around the gear selector lever. Remove the two screws 3 that secure the front of the console to the instrument panel. Engage the locating pin on the underside of the console rear bin into the slot in the top of the floor panel trans- mission tunnel.
Then slide trim stick up to the upper spring clip retainer, and pry to disengage clip. Using a trim stick or another suitable wide flat- bladed tool and starting nearest the B-pillar trim 2 , carefully pry the lower cowl trim 3 upward from the front door opening sill far enough to dis- engage the three spring clip retainers that secure the trim to the slots in the sill. These repair manuals will be useful to owners of Chrysler cars, mechanics, specialists of service stations, repair shops and car-care centers. All test and repair procedures on components or assemblies in non-automotive applications should be repaired in accordance with instructions supplied by the manufacturer of the total product. Locate the two alignment holes at the front of the console over the two alignment pins on the instrument panel. Position the mat 5 into the console rear bin with the curved edge oriented forward in the vehicle. Position the tabs on the underside of the console shifter bezel into the holes in the floor console.
Full maintenance guidance, from total teardown to complete rebuild, is available in our Chrysler 300 2005-2010 repair manual, available from Haynes in print and digital versions. These special tools should be used as recommended throughout this publication. Remove the upper cowl trim from the front of the front door opening. The 300 features components from a Mercedez Benz E-Class and boasts fully independent suspension with roll bar, disc brakes and four-speed automatic transmission. It was equipped with options of V6 and V8 engines ranging from 2. Tighten the bolts to 5 N·m 40 in. Remove the floor console from the vehicle.
Such information can be very rational in use by motorists, in case of necessity of repair procedures. The individua repairl manual includes a user manual for Chrysler, recommendations for maintenance, electrica circuits wiring diagrams. Position the mat 2 into the cubby bin at the front of the floor console. These are the same for manuals given to the workshop and contains detailed instructions and step by step diagrams for all workshop procedures everything from changing the plugs to rebuilding the engine, as well as electrical diagrams, torque settings, fluid capacities, etc. Open the lid of the console rear bin and remove the mat from the rear bin.