Front and Rear Wheels 7. Evaporative emission control system California models only? Refer to Service Manual, Page 8-8 2. Route black wire to battery negative connection as shown. On the left side, remove the footrest support mounting bolt 1 and footrest support bracket assembly 2. The Suzuki Boulevard - Intruder manual by Clymer is the best reference book for repair and service information for your Suzuki Intruder - Boulevard. The Indian and Philippine markets are usually in E-book format only, for these rare occasions I shall look on eBay and find the cheapest one available. The contents are listed on the first page of each section to help you find the item and page you need.
Install the lower screw 4 or 5 with the saddlebag guard, washer 9 and locknut 6 inside the frame. Order a Hanes book for your bike and it will help you more than the stock manual. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Good luck and have a wonderful day. Every Clymer motorcycle service manual contains hundreds of original photographs and illustrations obtained from the complete disassembly and assembly of the motorcycle covered. Refer to Service Manual, Page 8-8 2.
Good luck and have a wonderful day. Make sure you are qualified before you ride. Follow the instructions in the appropriate Service Manual or Instruction Sheet. Route Fuelpak green wire to T-tap on the factory black wire with brown stripe. Install saddlebag if removed following the instructions in the appropriate Service Manual or Instruction Sheet.
Remove Docking Hardware 1 2 is05320 1. As a result, the hands seen in the photographs are those of the author. Routh the Fuelpak violet wire to T-tap on the factory pink wire with black stripe as shown Fig 3 7. Within the Sections are numbered paragraphs. Remove and discard the forwardmost fender support bolt 1. If Fuelpak turns off when the horn is sounded, recheck the red wire connection on the horn and that it is connected to the orange wire from the factory harness.
The exhaust system becomes very hot during operation, and it remains hot after operation. Tighten exhaust shields following the instructions in the appropriate Service Manual. Move mufflers enough to access the rear bolt attaching the exhaust mounting bracket to the frame. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner, part number 94683-99. The speedometer pointer is driven by the stepping motor.
Now remove the breather hose at bottom of the air cleaner. You will not reuse this. Exhaust support bracket Figure 5. It is up to you how you decide to cut your motorcycles bodywork to accept the frame slider there are many different ways customers go through this process. Re-using these screws can result in torque loss and damage to brake components. Good luck and have a wonderful day. .
Good luck and have a wonderful day. Cover the throttle bodies to prevent anything from dropping into the engine. You should also wear a face shield or goggles; boots, gloves, and protective clothing. Route wiring harness as shown in the picture. The text of this manual is divided into sections. Good luck and have a wonderful day. Refer to Service Manual, Page 5-3 3.
Rear Wheel Removal i02495 1. Shim 1 size table Part number Thickness 24945-48G10-030 0. Tighten exhaust header bolts following the instructions in the appropriate Service Manual. For 2005-2006 Models: Install lower screw 3 through the saddlebag guard, saddlebag guard spacer 8 , footpeg support and the frame. Motorcycle manufacturers continually make changes to specifications and recommendations, and these, when notified,mare incorporated into our manuals at the earliest opportunity. Good luck and have a nice day. Most countries require a special riding test or license.
It contains everything you will need to repair, maintain, rebuild, refurbish or restore your motorcycle. Install the new wheel to the rear fork. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. Loosely install upper screw 7 through the saddlebag guard and the fender support. Loosely install the exhaust header bolts. Most of the manuals will cover your exact make, model, and year otherwise one will be provided that comes as close as possible to your bike and will have most of the same info that an exact manual would have.