Install the washers, and then install the nuts. Yfm400 Kodiak 400 Manual Pdf can be very useful guide, and Yfm400 Kodiak 400 Manual Pdf play an important role in your products. If necessary, apply 14 inches in depth. If there is room to do so by steering in the direc- unexpected and uncorrected, sliding could tion of the slide. Store it in a dry place and recharge it once a month. Remove panels E and F. Put the tongue of sense and good judgment when carrying car- the loaded trailer on the scale with the go or towing a trailer.
Install a new bulb in the bulb holder by pushing it inward and turning it clockwise. Always shield eyes when working tery. Make sure that this area choke to the closed position, and shift the is free of obstacles and other riders. Remove the nuts together with the wash- ers. Pull off the lock plate, and then remove the air filter element from its frame. Most A diagnostic tachometer must be used for this adjusting should be left to a Yamaha dealer procedure.
Before riding, check that the brake fluid is above the minimum level mark and replenish when necessary. Lubricate the inner cables and the cable ends. Install the drain bolt, and then tighten it to the specified torque. Your Yamaha dealer has a variety of an accessory that limits your ability to move genuine Yamaha accessories. Automotive type wax may be applied to ing. See page 6-1 for details.
Be sure to read each section on the room. Remove the nuts from the wheel. On extremely slippery surfaces, such as ice, go slowly and be very cautious in order to reduce the chance of skidding or sliding out of con- trol. Open the throttle lever gradually and con- tinue to watch to the rear while backing. If the fuel tank is overfilled, damage or vehicle performance problems.
You drive select lever into the forward position. Ride cau- tiously in unfamiliar areas. The fuel cock has three positions. See pages 8-11—8-12 for panel removal and installation proce- dures. Ignition Wipe clean with dry cloth. Consult a Yamaha dealer if you 1.
Headlight bulb holder tab × 2 1. Pull it toward the handlebar to ap- ply the front brake. An improper fuse can cause damage to the electrical system which could lead to a fire. Install the bulb holder together with the bulb by turning it clockwise. Replacement of brake components re- quires professional knowledge.
The coolant lev- Removing the radiator cap when the en- el will vary with engine temperature. If the battery seems to have discharged, consult a Yamaha dealer. Never go over the top of a hill at high speed. Torque wrench Tightening torque: Oil filter cartridge: 17 Nm 1. Rear axle boot × 2 each side 1. To install Place the panel in the original position and in- stall the bolt. To decrease the spring preload, turn the ad- justing ring in direction b.
Refer to this section each time a panel has to be removed or reinstalled. Pull outward on the areas shown, and then pull upward. Move in direction b to turn off the starter choke. Standard position: 2 1- Minimum soft 5- Maximum hard 4-20. Drive select lever box check hose 1.
After break-in: Avoid prolonged full throttle operation. With the purchase of this Yamaha, you can now appreciate the high degree of crafts- manship and reliability that have made Yamaha a leader in these fields. Remove the air filter element assembly. Adjust the spring preload as follows. See pages 8-7—8-8 for panel removal and installation proce- dures. Shift the drive select lever into the neutral. All the torque settings and adjust them as neces- parts and accessories added to this ve- sary.
When storing any documents in the storage Maximum load limit: 80 kg 176 lb compartment, be sure to wrap them in a plas-. . A separate starter circuit supplies this mixture. You must use common with a bathroom scale. Take the machine to a Yamaha dealer or refer to the Service Manual for correct tightening torque. The engine can be started in any gear if the rear brake lever or brake pedal is ap- plied.